From 5d6450e4b5cbb5faee484c9bfdcd1eeb25e72663 Mon Sep 17 00:00:00 2001
From: klipper <klipper@home>
Date: Mon, 7 Sep 2026 00:28:51 +0200
Subject: [PATCH] printer.cfg modified - 07.09.2026 - 00:28:43

---
 printer_data/config/ebb36.cfg      | 36 +++++-------------------------
 printer_data/config/moonraker.conf |  4 ++--
 printer_data/config/printer.cfg    | 10 ++++-----
 3 files changed, 12 insertions(+), 38 deletions(-)

diff --git a/printer_data/config/ebb36.cfg b/printer_data/config/ebb36.cfg
index 4fc357d..3b425cc 100644
--- a/printer_data/config/ebb36.cfg
+++ b/printer_data/config/ebb36.cfg
@@ -1,38 +1,14 @@
-# This file contains common pin mappings for the BIGTREETECH EBBCan
-# Canbus board. To use this config, the firmware should be compiled for the
-# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)".
-# The "EBB Can" micro-controller will be used to control the components on the nozzle.
+# Active toolhead controller: BIGTREETECH EBB with STM32G0B1xx (PCB revision not confirmed).
+# Runtime transport: CAN on PB0/PB1 at 1,000,000 bit/s; application starts at 0x08000000.
+# No Katapult bootloader was detected. Do not use an RP2040 image or assume remote CAN flashing.
+# The EBB micro-controller controls the toolhead components.
 
 # See docs/Config_Reference.md for a description of parameters.
 
-
-# [temperature_sensor EBB_NTC]
-# sensor_type: Generic 3950
-# sensor_pin: EBBCan:gpio28
-
-# [adxl345]
-# cs_pin: EBBCan:gpio1
-# spi_software_sclk_pin: EBBCan:gpio2
-# spi_software_mosi_pin: EBBCan:gpio0
-# spi_software_miso_pin: EBBCan:gpio3
-# axes_map: z,-y,x
-
-# [resonance_tester]
-# probe_points: 100, 100, 20
-# accel_chip: adxl345
-
-
-
-
-
 [mcu EBBCan]
 canbus_uuid: 2bfe734774a0
 
-# [adxl345]
-# cs_pin: EBBCan: PB12
-# spi_bus: spi2_PB2_PB11_PB10
-# axes_map: x,y,z
-
+# ADXL345 is provided by Cartographer; legacy EBB accelerometer examples stay removed.
 
 [extruder]
 ##  Update value below when you perform extruder calibration
@@ -85,5 +61,3 @@ heater: extruder
 heater_temp: 50.0
 max_power: 1.0
 kick_start_time: 0.5
-
-
diff --git a/printer_data/config/moonraker.conf b/printer_data/config/moonraker.conf
index 157f3d1..23f80f8 100644
--- a/printer_data/config/moonraker.conf
+++ b/printer_data/config/moonraker.conf
@@ -67,7 +67,7 @@ managed_services: klipper moonraker
 type: git_repo
 path: ~/KlipperScreen
 origin: https://github.com/jordanruthe/KlipperScreen.git
-env: ~/.KlipperScreen-env/bin/python
+virtualenv: ~/.KlipperScreen-env
 requirements: scripts/KlipperScreen-requirements.txt
 install_script: scripts/KlipperScreen-install.sh
 managed_services: KlipperScreen
@@ -105,4 +105,4 @@ type: git_repo
 path: ~/klipper-backup
 origin: https://github.com/Staubgeborener/klipper-backup.git
 managed_services: moonraker
-primary_branch: main
\ No newline at end of file
+primary_branch: main
diff --git a/printer_data/config/printer.cfg b/printer_data/config/printer.cfg
index 9c1aa02..57b88bd 100644
--- a/printer_data/config/printer.cfg
+++ b/printer_data/config/printer.cfg
@@ -1,13 +1,13 @@
-# This file contains common pin mappings for the BigTreeTech Octopus V1.
-# To use this config, the firmware should be compiled for the STM32F446 with a "32KiB bootloader"
-# Enable "extra low-level configuration options" and select the "12MHz crystal" as clock reference
+# Active mainboard: BigTreeTech Octopus family with STM32F407xx (PCB revision not confirmed).
+# Firmware profile: 32KiB factory SD bootloader, 8MHz crystal, USB on PA11/PA12.
+# Do not substitute the STM32F446/12MHz profile; runtime hardware was verified on 2026-09-06.
 
 # after running "make", copy the generated "klipper/out/klipper.bin" file to a
-# file named "firmware.bin" on an SD card and then restart the OctoPus with that SD card.
+# file named "firmware.bin" on an SD card and then restart the Octopus with that SD card.
 
 # See docs/Config_Reference.md for a description of parameters.
 
-## Voron Design VORON2 250/300/350mm BigTreeTech OctoPus V1 TMC2209 UART config
+## Voron Design VORON2 250mm; BigTreeTech Octopus-family STM32F407; TMC2209 UART.
 
 ## *** THINGS TO CHANGE/CHECK: ***
 ## MCU paths                            [mcu] section