From d0fc210dc7994bec81c9a59eb15d55fa86bf7868 Mon Sep 17 00:00:00 2001 From: klipper Date: Sun, 6 Sep 2026 22:41:04 +0200 Subject: [PATCH] KlipperScreen.conf modified - 06.09.2026 - 22:40:45 --- printer_data/config/cartographer.cfg | 28 --------- printer_data/config/crowsnest.conf | 55 ----------------- printer_data/config/ebb36.cfg | 89 ---------------------------- 3 files changed, 172 deletions(-) delete mode 100644 printer_data/config/cartographer.cfg delete mode 100644 printer_data/config/crowsnest.conf delete mode 100644 printer_data/config/ebb36.cfg diff --git a/printer_data/config/cartographer.cfg b/printer_data/config/cartographer.cfg deleted file mode 100644 index 27b024e..0000000 --- a/printer_data/config/cartographer.cfg +++ /dev/null @@ -1,28 +0,0 @@ -[mcu cartographer] - -canbus_uuid: fa54c42a161b - - -[cartographer] -mcu: cartographer -# Offsets are measured from the centre of your coil, to the tip of your nozzle -# on a level axis. It is vital that this is accurate. -x_offset: 0 -# adjust for your cartographers offset from nozzle to middle of coil -y_offset: 25 -# adjust for your cartographers offset from nozzle to middle of coil - -[adxl345] -cs_pin: cartographer:PA3 -spi_bus: spi1 - -[resonance_tester] -accel_chip: adxl345 -probe_points: - 125, 125, 20 - -[temperature_sensor Cartographer_MCU] -sensor_type: temperature_mcu -sensor_mcu: cartographer -min_temp: 0 -max_temp: 105 diff --git a/printer_data/config/crowsnest.conf b/printer_data/config/crowsnest.conf deleted file mode 100644 index 977ed33..0000000 --- a/printer_data/config/crowsnest.conf +++ /dev/null @@ -1,55 +0,0 @@ -#### crowsnest.conf -#### This is a typical default config. -#### Also used as default in mainsail / MainsailOS -#### See: -#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md -#### for details to configure to your needs. - - -##################################################################### -#### ##### -#### Information about ports and according URL's ##### -#### ##### -##################################################################### -#### ##### -#### Port 8080 equals /webcam/?action=[stream/snapshot] ##### -#### Port 8081 equals /webcam2/?action=[stream/snapshot] ##### -#### Port 8082 equals /webcam3/?action=[stream/snapshot] ##### -#### Port 8083 equals /webcam4/?action=[stream/snapshot] ##### -#### ##### -##################################################################### - - -[crowsnest] -log_path: ~/printer_data/logs/crowsnest.log -log_level: verbose # Valid Options are quiet/verbose/debug -delete_log: false # Deletes log on every restart, if set to true - -[cam android] -mode: mjpg # mjpg/rtsp -port: 80 # Port -device: http://192.168.0.117:4747/video # See Log for available ... -resolution: 640x480 # widthxheight format -max_fps: 15 # If Hardware Supports this it will be forced, otherwise ignored/coerced. -#custom_flags: # You can run the Stream Services with custom flags. -#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of. - -[cam c930] -mode: mjpg # mjpg/rtsp -port: 8080 # Port -device: /dev/video0 # See Log for available ... -resolution: 1280x720 # widthxheight format -max_fps: 30 # If Hardware Supports this it will be forced, otherwise ignored/coerced. -#custom_flags: # You can run the Stream Services with custom flags. -#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of. - -[cam custom] -mode: mjpg # mjpg/rtsp -port: 8081 # Port -device: /dev/video2 # See Log for available ... -resolution: 1280x720 # widthxheight format -max_fps: 30 # If Hardware Supports this it will be forced, otherwise ignored/coerced. -#custom_flags: # You can run the Stream Services with custom flags. -#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of. - - diff --git a/printer_data/config/ebb36.cfg b/printer_data/config/ebb36.cfg deleted file mode 100644 index 4fc357d..0000000 --- a/printer_data/config/ebb36.cfg +++ /dev/null @@ -1,89 +0,0 @@ -# This file contains common pin mappings for the BIGTREETECH EBBCan -# Canbus board. To use this config, the firmware should be compiled for the -# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)". -# The "EBB Can" micro-controller will be used to control the components on the nozzle. - -# See docs/Config_Reference.md for a description of parameters. - - -# [temperature_sensor EBB_NTC] -# sensor_type: Generic 3950 -# sensor_pin: EBBCan:gpio28 - -# [adxl345] -# cs_pin: EBBCan:gpio1 -# spi_software_sclk_pin: EBBCan:gpio2 -# spi_software_mosi_pin: EBBCan:gpio0 -# spi_software_miso_pin: EBBCan:gpio3 -# axes_map: z,-y,x - -# [resonance_tester] -# probe_points: 100, 100, 20 -# accel_chip: adxl345 - - - - - -[mcu EBBCan] -canbus_uuid: 2bfe734774a0 - -# [adxl345] -# cs_pin: EBBCan: PB12 -# spi_bus: spi2_PB2_PB11_PB10 -# axes_map: x,y,z - - -[extruder] -## Update value below when you perform extruder calibration -## If you ask for 100mm of filament, but in reality it is 98mm: -## rotation_distance = * / 100 -rotation_distance: 47.088 -gear_ratio: 9:1 -microsteps: 16 -full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree -nozzle_diameter: 0.340 -filament_diameter: 1.75 -max_extrude_only_distance: 50 -min_temp: 10 -max_temp: 300 -max_power: 1.0 -min_extrude_temp: 170 -max_extrude_cross_section: 5 - -## Try to keep pressure_advance below 1.0 -pressure_advance: 0.038 -## Default is 0.040, leave stock -#pressure_advance_smooth_time: 0.040 -step_pin: EBBCan: PD0 -dir_pin: EBBCan: PD1 -enable_pin: !EBBCan: PD2 -heater_pin: EBBCan: PB13 -sensor_type: MAX31865 -sensor_pin: EBBCan: PA4 -spi_bus: spi1 -rtd_nominal_r: 1000 -rtd_reference_r: 4300 -rtd_num_of_wires: 2 - - -[tmc2209 extruder] -uart_pin: EBBCan: PA15 -run_current: 0.650 -stealthchop_threshold: 999999 - -[fan] -pin: EBBCan: PA1 -kick_start_time: 0.5 -hardware_pwm: false -cycle_time: 0.01 -off_below: 0.1 - -[heater_fan hotend_fan] -pin: EBBCan: PA0 -heater: extruder -heater_temp: 50.0 -max_power: 1.0 -kick_start_time: 0.5 - -