64 lines
1.7 KiB
Plaintext
64 lines
1.7 KiB
Plaintext
# Active toolhead controller: BIGTREETECH EBB with STM32G0B1xx (PCB revision not confirmed).
|
|
# Runtime transport: CAN on PB0/PB1 at 1,000,000 bit/s; application starts at 0x08000000.
|
|
# No Katapult bootloader was detected. Do not use an RP2040 image or assume remote CAN flashing.
|
|
# The EBB micro-controller controls the toolhead components.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
[mcu EBBCan]
|
|
canbus_uuid: 2bfe734774a0
|
|
|
|
# ADXL345 is provided by Cartographer; legacy EBB accelerometer examples stay removed.
|
|
|
|
[extruder]
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
rotation_distance: 22.6789511
|
|
gear_ratio: 50:10
|
|
microsteps: 16
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.400
|
|
filament_diameter: 1.75
|
|
max_extrude_only_distance: 50
|
|
min_temp: 10
|
|
max_temp: 300
|
|
max_power: 1.0
|
|
min_extrude_temp: 170
|
|
# Use Klipper's safety default: 4 * nozzle_diameter^2 = 0.64 mm^2 for a 0.4 mm nozzle.
|
|
|
|
## Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.038
|
|
## Default is 0.040, leave stock
|
|
#pressure_advance_smooth_time: 0.040
|
|
step_pin: EBBCan: PD0
|
|
dir_pin: EBBCan: PD1
|
|
enable_pin: !EBBCan: PD2
|
|
heater_pin: EBBCan: PB13
|
|
sensor_type: MAX31865
|
|
sensor_pin: EBBCan: PA4
|
|
spi_bus: spi1
|
|
rtd_nominal_r: 1000
|
|
rtd_reference_r: 4300
|
|
rtd_num_of_wires: 2
|
|
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBBCan: PA15
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[fan]
|
|
pin: EBBCan: PA1
|
|
kick_start_time: 0.5
|
|
hardware_pwm: false
|
|
cycle_time: 0.01
|
|
off_below: 0.1
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: EBBCan: PA0
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|