New Backup on boot - 06.09.2026 - 23:17:14

2026-09-06 23:17:36 +02:00
1 parent d0fc210dc7
commit 63b4b4a0bd
@@ -0,0 +1,28 @@
+[mcu cartographer]
+
+canbus_uuid: fa54c42a161b
+
+
+[cartographer]
+mcu: cartographer            
+#   Offsets are measured from the centre of your coil, to the tip of your nozzle 
+#   on a level axis. It is vital that this is accurate. 
+x_offset: 0                          
+#    adjust for your cartographers offset from nozzle to middle of coil
+y_offset: 25                        
+#    adjust for your cartographers offset from nozzle to middle of coil
+
+[adxl345]
+cs_pin: cartographer:PA3
+spi_bus: spi1
+
+[resonance_tester]
+accel_chip: adxl345
+probe_points:
+    125, 125, 20
+
+[temperature_sensor Cartographer_MCU]
+sensor_type: temperature_mcu
+sensor_mcu: cartographer
+min_temp: 0
+max_temp: 105
@@ -0,0 +1,55 @@
+#### crowsnest.conf
+#### This is a typical default config.
+#### Also used as default in mainsail / MainsailOS
+#### See:
+#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md
+#### for details to configure to your needs.
+
+
+#####################################################################
+####                                                            #####
+####      Information about ports and according URL's           #####
+####                                                            #####
+#####################################################################
+####                                                            #####
+####    Port 8080 equals /webcam/?action=[stream/snapshot]      #####
+####    Port 8081 equals /webcam2/?action=[stream/snapshot]     #####
+####    Port 8082 equals /webcam3/?action=[stream/snapshot]     #####
+####    Port 8083 equals /webcam4/?action=[stream/snapshot]     #####
+####                                                            #####
+#####################################################################
+
+
+[crowsnest]
+log_path: ~/printer_data/logs/crowsnest.log
+log_level: verbose                      # Valid Options are quiet/verbose/debug
+delete_log: false                       # Deletes log on every restart, if set to true
+
+[cam android]
+mode: mjpg                              # mjpg/rtsp
+port: 80                                # Port
+device: http://192.168.0.117:4747/video                     # See Log for available ...
+resolution: 640x480                     # widthxheight format
+max_fps: 15                             # If Hardware Supports this it will be forced, otherwise ignored/coerced.
+#custom_flags:                          # You can run the Stream Services with custom flags.
+#v4l2ctl:                               # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
+
+[cam c930]
+mode: mjpg                              # mjpg/rtsp
+port: 8080                                # Port
+device: /dev/video0                 # See Log for available ...
+resolution: 1280x720               # widthxheight format
+max_fps: 30                             # If Hardware Supports this it will be forced, otherwise ignored/coerced.
+#custom_flags:                          # You can run the Stream Services with custom flags.
+#v4l2ctl:                               # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
+
+[cam custom]
+mode: mjpg                              # mjpg/rtsp
+port: 8081                                # Port
+device: /dev/video2                 # See Log for available ...
+resolution: 1280x720               # widthxheight format
+max_fps: 30                             # If Hardware Supports this it will be forced, otherwise ignored/coerced.
+#custom_flags:                          # You can run the Stream Services with custom flags.
+#v4l2ctl:                               # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
+
+
@@ -0,0 +1,89 @@
+# This file contains common pin mappings for the BIGTREETECH EBBCan
+# Canbus board. To use this config, the firmware should be compiled for the
+# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)".
+# The "EBB Can" micro-controller will be used to control the components on the nozzle.
+
+# See docs/Config_Reference.md for a description of parameters.
+
+
+# [temperature_sensor EBB_NTC]
+# sensor_type: Generic 3950
+# sensor_pin: EBBCan:gpio28
+
+# [adxl345]
+# cs_pin: EBBCan:gpio1
+# spi_software_sclk_pin: EBBCan:gpio2
+# spi_software_mosi_pin: EBBCan:gpio0
+# spi_software_miso_pin: EBBCan:gpio3
+# axes_map: z,-y,x
+
+# [resonance_tester]
+# probe_points: 100, 100, 20
+# accel_chip: adxl345
+
+
+
+
+
+[mcu EBBCan]
+canbus_uuid: 2bfe734774a0
+
+# [adxl345]
+# cs_pin: EBBCan: PB12
+# spi_bus: spi2_PB2_PB11_PB10
+# axes_map: x,y,z
+
+
+[extruder]
+##  Update value below when you perform extruder calibration
+##  If you ask for 100mm of filament, but in reality it is 98mm:
+##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
+rotation_distance: 47.088
+gear_ratio: 9:1
+microsteps: 16
+full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
+nozzle_diameter: 0.340
+filament_diameter: 1.75
+max_extrude_only_distance: 50
+min_temp: 10
+max_temp: 300
+max_power: 1.0
+min_extrude_temp: 170
+max_extrude_cross_section: 5
+
+##  Try to keep pressure_advance below 1.0
+pressure_advance: 0.038
+##  Default is 0.040, leave stock
+#pressure_advance_smooth_time: 0.040
+step_pin: EBBCan: PD0
+dir_pin: EBBCan: PD1
+enable_pin: !EBBCan: PD2
+heater_pin: EBBCan: PB13
+sensor_type: MAX31865
+sensor_pin: EBBCan: PA4
+spi_bus: spi1
+rtd_nominal_r: 1000
+rtd_reference_r: 4300
+rtd_num_of_wires: 2
+
+
+[tmc2209 extruder]
+uart_pin: EBBCan: PA15
+run_current: 0.650
+stealthchop_threshold: 999999
+
+[fan]
+pin: EBBCan: PA1
+kick_start_time: 0.5
+hardware_pwm: false
+cycle_time: 0.01
+off_below: 0.1
+
+[heater_fan hotend_fan]
+pin: EBBCan: PA0
+heater: extruder
+heater_temp: 50.0
+max_power: 1.0
+kick_start_time: 0.5
+
+