New Backup on boot - 07.10.2026 - 01:17:14
This commit is contained in:
klipper committed
1 parent
833d0c63e5
commit
7aa60b1c32
10 files changed
+540
No files matched your search
@@ -0,0 +1,36 @@
|
||||
# Below you can include specific configuration files depending on what you want KAMP to do:
|
||||
|
||||
# [include ./KAMP/Adaptive_Meshing.cfg] # Include to enable adaptive meshing configuration.
|
||||
[include ./KAMP/Line_Purge.cfg] # Include to enable adaptive line purging configuration.
|
||||
#[include ./KAMP/Voron_Purge.cfg] # Include to enable adaptive Voron logo purging configuration.
|
||||
# [include ./KAMP/Smart_Park.cfg] # Include to enable the Smart Park function, which parks the printhead near the print area for final heating.
|
||||
|
||||
[gcode_macro _KAMP_Settings]
|
||||
description: This macro contains all adjustable settings for KAMP
|
||||
|
||||
# The following variables are settings for KAMP as a whole.
|
||||
variable_verbose_enable: True # Set to True to enable KAMP information output when running. This is useful for debugging.
|
||||
|
||||
# The following variables are for adjusting adaptive mesh settings for KAMP.
|
||||
variable_mesh_margin: 0 # Expands the mesh size in millimeters if desired. Leave at 0 to disable.
|
||||
variable_fuzz_amount: 10 # Slightly randomizes mesh points to spread out wear from nozzle-based probes. Leave at 0 to disable.
|
||||
|
||||
# The following variables are for those with a dockable probe like Klicky, Euclid, etc. # ---------------- Attach Macro | Detach Macro
|
||||
variable_probe_dock_enable: False # Set to True to enable the usage of a dockable probe. # ---------------------------------------------
|
||||
variable_attach_macro: 'Attach_Probe' # The macro that is used to attach the probe. # Klicky Probe: 'Attach_Probe' | 'Dock_Probe'
|
||||
variable_detach_macro: 'Dock_Probe' # The macro that is used to store the probe. # Euclid Probe: 'Deploy_Probe' | 'Stow_Probe'
|
||||
# Legacy Gcode: 'M401' | 'M402'
|
||||
|
||||
# The following variables are for adjusting adaptive purge settings for KAMP.
|
||||
variable_purge_height: 0.8 # Z position of nozzle during purge, default is 0.8.
|
||||
variable_tip_distance: 0 # Distance between tip of filament and nozzle before purge. Should be similar to PRINT_END final retract amount.
|
||||
variable_purge_margin: 10 # Distance the purge will be in front of the print area, default is 10.
|
||||
variable_purge_amount: 30 # Amount of filament to be purged prior to printing.
|
||||
variable_flow_rate: 12 # Flow rate of purge in mm3/s. Default is 12.
|
||||
|
||||
# The following variables are for adjusting the Smart Park feature for KAMP, which will park the printhead near the print area at a specified height.
|
||||
variable_smart_park_height: 10 # Z position for Smart Park, default is 10.
|
||||
|
||||
gcode: # Gcode section left intentionally blank. Do not disturb.
|
||||
|
||||
{action_respond_info(" Running the KAMP_Settings macro does nothing, it is only used for storing KAMP settings. ")}
|
||||
@@ -0,0 +1,32 @@
|
||||
|
||||
#~# --- Do not edit below this line. This section is auto generated --- #~#
|
||||
#~#
|
||||
#~# [main]
|
||||
#~# theme = material-darker
|
||||
#~# print_estimate_method = file
|
||||
#~# screen_blanking = 300
|
||||
#~# screen_blanking_printing = 300
|
||||
#~# font_size = small
|
||||
#~# confirm_estop = True
|
||||
#~# show_heater_power = True
|
||||
#~# move_speed_xy = 500
|
||||
#~# move_speed_z = 30
|
||||
#~# print_sort_dir = date_desc
|
||||
#~# language = pl
|
||||
#~#
|
||||
#~# [displayed_macros Printer]
|
||||
#~# clean_nozzle = False
|
||||
#~# g32 = False
|
||||
#~# line_purge = False
|
||||
#~# nvmoff = False
|
||||
#~# print_end = False
|
||||
#~# park = False
|
||||
#~# nvmon = False
|
||||
#~# print_start = False
|
||||
#~#
|
||||
#~# [graph Printer]
|
||||
#~# temperature_sensor raspberry_pi = False
|
||||
#~# temperature_sensor mcu_temp = False
|
||||
#~# temperature_sensor ebb_ntc = False
|
||||
#~# extruder = False
|
||||
#~#
|
||||
@@ -0,0 +1,28 @@
|
||||
[mcu cartographer]
|
||||
|
||||
canbus_uuid: fa54c42a161b
|
||||
|
||||
|
||||
[cartographer]
|
||||
mcu: cartographer
|
||||
# Offsets are measured from the centre of your coil, to the tip of your nozzle
|
||||
# on a level axis. It is vital that this is accurate.
|
||||
x_offset: 0
|
||||
# adjust for your cartographers offset from nozzle to middle of coil
|
||||
y_offset: 25
|
||||
# adjust for your cartographers offset from nozzle to middle of coil
|
||||
|
||||
[adxl345]
|
||||
cs_pin: cartographer:PA3
|
||||
spi_bus: spi1
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
125, 125, 20
|
||||
|
||||
[temperature_sensor Cartographer_MCU]
|
||||
sensor_type: temperature_mcu
|
||||
sensor_mcu: cartographer
|
||||
min_temp: 0
|
||||
max_temp: 105
|
||||
@@ -0,0 +1,43 @@
|
||||
#### crowsnest.conf
|
||||
#### This is a typical default config.
|
||||
#### Also used as default in mainsail / MainsailOS
|
||||
#### See:
|
||||
#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md
|
||||
#### for details to configure to your needs.
|
||||
|
||||
|
||||
#####################################################################
|
||||
#### #####
|
||||
#### Information about ports and according URL's #####
|
||||
#### #####
|
||||
#####################################################################
|
||||
#### #####
|
||||
#### Port 8080 equals /webcam/?action=[stream/snapshot] #####
|
||||
#### Port 8081 equals /webcam2/?action=[stream/snapshot] #####
|
||||
#### Port 8082 equals /webcam3/?action=[stream/snapshot] #####
|
||||
#### Port 8083 equals /webcam4/?action=[stream/snapshot] #####
|
||||
#### #####
|
||||
#####################################################################
|
||||
|
||||
|
||||
[crowsnest]
|
||||
log_path: ~/printer_data/logs/crowsnest.log
|
||||
log_level: verbose
|
||||
delete_log: true
|
||||
|
||||
[cam chamber]
|
||||
mode: mjpg
|
||||
port: 8080
|
||||
device: /dev/v4l/by-id/usb-HZ_USB_Camera_20220301104-video-index0
|
||||
resolution: 1280x720
|
||||
max_fps: 30
|
||||
|
||||
[cam c930e]
|
||||
mode: mjpg
|
||||
port: 8081
|
||||
device: /dev/v4l/by-id/usb-046d_Logitech_Webcam_C930e_CA4F3EDE-video-index0
|
||||
resolution: 1280x720
|
||||
max_fps: 30
|
||||
# 50 Hz avoids mains-light flicker. Fixed focus prevents the autofocus from
|
||||
# hunting when the toolhead crosses the centre of the frame.
|
||||
v4l2ctl: power_line_frequency=1,exposure_dynamic_framerate=0,focus_automatic_continuous=0,focus_absolute=0
|
||||
@@ -0,0 +1,63 @@
|
||||
# Active toolhead controller: BIGTREETECH EBB with STM32G0B1xx (PCB revision not confirmed).
|
||||
# Runtime transport: CAN on PB0/PB1 at 1,000,000 bit/s; application starts at 0x08000000.
|
||||
# No Katapult bootloader was detected. Do not use an RP2040 image or assume remote CAN flashing.
|
||||
# The EBB micro-controller controls the toolhead components.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu EBBCan]
|
||||
canbus_uuid: 2bfe734774a0
|
||||
|
||||
# ADXL345 is provided by Cartographer; legacy EBB accelerometer examples stay removed.
|
||||
|
||||
[extruder]
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
rotation_distance: 21.778614
|
||||
gear_ratio: 50:10
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
max_extrude_only_distance: 50
|
||||
min_temp: 10
|
||||
max_temp: 300
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
# Use Klipper's safety default: 4 * nozzle_diameter^2 = 0.64 mm^2 for a 0.4 mm nozzle.
|
||||
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.038
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
step_pin: EBBCan: PD0
|
||||
dir_pin: !EBBCan: PD1
|
||||
enable_pin: !EBBCan: PD2
|
||||
heater_pin: EBBCan: PB13
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: EBBCan: PA4
|
||||
spi_bus: spi1
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 4300
|
||||
rtd_num_of_wires: 2
|
||||
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: EBBCan: PA15
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[fan]
|
||||
pin: EBBCan: PA1
|
||||
kick_start_time: 0.5
|
||||
hardware_pwm: false
|
||||
cycle_time: 0.01
|
||||
off_below: 0.1
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: EBBCan: PA0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
@@ -0,0 +1,63 @@
|
||||
# Active toolhead controller: BIGTREETECH EBB with STM32G0B1xx (PCB revision not confirmed).
|
||||
# Runtime transport: CAN on PB0/PB1 at 1,000,000 bit/s; application starts at 0x08000000.
|
||||
# No Katapult bootloader was detected. Do not use an RP2040 image or assume remote CAN flashing.
|
||||
# The EBB micro-controller controls the toolhead components.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu EBBCan]
|
||||
canbus_uuid: 2bfe734774a0
|
||||
|
||||
# ADXL345 is provided by Cartographer; legacy EBB accelerometer examples stay removed.
|
||||
|
||||
[extruder]
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
rotation_distance: 47.088
|
||||
gear_ratio: 9:1
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
max_extrude_only_distance: 50
|
||||
min_temp: 10
|
||||
max_temp: 300
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
# Use Klipper's safety default: 4 * nozzle_diameter^2 = 0.64 mm^2 for a 0.4 mm nozzle.
|
||||
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.038
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
step_pin: EBBCan: PD0
|
||||
dir_pin: EBBCan: PD1
|
||||
enable_pin: !EBBCan: PD2
|
||||
heater_pin: EBBCan: PB13
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: EBBCan: PA4
|
||||
spi_bus: spi1
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 4300
|
||||
rtd_num_of_wires: 2
|
||||
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: EBBCan: PA15
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[fan]
|
||||
pin: EBBCan: PA1
|
||||
kick_start_time: 0.5
|
||||
hardware_pwm: false
|
||||
cycle_time: 0.01
|
||||
off_below: 0.1
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: EBBCan: PA0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
@@ -0,0 +1,63 @@
|
||||
# Active toolhead controller: BIGTREETECH EBB with STM32G0B1xx (PCB revision not confirmed).
|
||||
# Runtime transport: CAN on PB0/PB1 at 1,000,000 bit/s; application starts at 0x08000000.
|
||||
# No Katapult bootloader was detected. Do not use an RP2040 image or assume remote CAN flashing.
|
||||
# The EBB micro-controller controls the toolhead components.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
[mcu EBBCan]
|
||||
canbus_uuid: 2bfe734774a0
|
||||
|
||||
# ADXL345 is provided by Cartographer; legacy EBB accelerometer examples stay removed.
|
||||
|
||||
[extruder]
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
rotation_distance: 22.6789511
|
||||
gear_ratio: 50:10
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.400
|
||||
filament_diameter: 1.75
|
||||
max_extrude_only_distance: 50
|
||||
min_temp: 10
|
||||
max_temp: 300
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
# Use Klipper's safety default: 4 * nozzle_diameter^2 = 0.64 mm^2 for a 0.4 mm nozzle.
|
||||
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.038
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
step_pin: EBBCan: PD0
|
||||
dir_pin: EBBCan: PD1
|
||||
enable_pin: !EBBCan: PD2
|
||||
heater_pin: EBBCan: PB13
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: EBBCan: PA4
|
||||
spi_bus: spi1
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 4300
|
||||
rtd_num_of_wires: 2
|
||||
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: EBBCan: PA15
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[fan]
|
||||
pin: EBBCan: PA1
|
||||
kick_start_time: 0.5
|
||||
hardware_pwm: false
|
||||
cycle_time: 0.01
|
||||
off_below: 0.1
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: EBBCan: PA0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
@@ -0,0 +1,96 @@
|
||||
# Note you may need to add the following to your printer.cfg somewhere (without the comments of course) for the Kinematic position stuff below to work.
|
||||
#[force_move]
|
||||
#enable_force_move: True
|
||||
|
||||
[gcode_macro _HOME_X]
|
||||
gcode:
|
||||
# Home
|
||||
{% set RUN_CURRENT_X = printer.configfile.settings['tmc2209 stepper_x'].run_current|float %}
|
||||
{% set RUN_CURRENT_Y = printer.configfile.settings['tmc2209 stepper_y'].run_current|float %}
|
||||
{% set HOME_CURRENT = 0.49 %}
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CURRENT}
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CURRENT}
|
||||
|
||||
SET_KINEMATIC_POSITION X=15 SET_HOMED=X
|
||||
G91
|
||||
G1 X15 F1200
|
||||
|
||||
# Finish the release move, then let the TMC StallGuard flag clear.
|
||||
M400
|
||||
G4 P2000
|
||||
G28 X
|
||||
|
||||
# Move away
|
||||
G91
|
||||
G1 X15 F1200
|
||||
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CURRENT_X}
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CURRENT_Y}
|
||||
|
||||
[gcode_macro _HOME_Y]
|
||||
gcode:
|
||||
{% set RUN_CURRENT_X = printer.configfile.settings['tmc2209 stepper_x'].run_current|float %}
|
||||
{% set RUN_CURRENT_Y = printer.configfile.settings['tmc2209 stepper_y'].run_current|float %}
|
||||
{% set HOME_CURRENT = 0.49 %}
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={HOME_CURRENT}
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={HOME_CURRENT}
|
||||
|
||||
SET_KINEMATIC_POSITION Y=15 SET_HOMED=Y
|
||||
G91
|
||||
G1 Y-15 F1200
|
||||
|
||||
# Y uses the physical endstop on PG9; finish the release move first.
|
||||
M400
|
||||
|
||||
# Home
|
||||
G28 Y
|
||||
# Move away
|
||||
G91
|
||||
G1 Y-15 F1200
|
||||
|
||||
# Restore normal CoreXY motor currents after moving off the endstop.
|
||||
SET_TMC_CURRENT STEPPER=stepper_x CURRENT={RUN_CURRENT_X}
|
||||
SET_TMC_CURRENT STEPPER=stepper_y CURRENT={RUN_CURRENT_Y}
|
||||
|
||||
[homing_override]
|
||||
axes: xyz
|
||||
gcode:
|
||||
{% set homed_axes = printer.toolhead.homed_axes|lower %}
|
||||
{% set home_all = 'X' not in params and 'Y' not in params and 'Z' not in params %}
|
||||
{% set home_z = home_all or 'Z' in params %}
|
||||
{% set home_x = home_all or 'X' in params or (home_z and 'x' not in homed_axes) %}
|
||||
{% set home_y = home_all or 'Y' in params or (home_z and 'y' not in homed_axes) %}
|
||||
{% set z_was_homed = 'z' in homed_axes %}
|
||||
|
||||
SAVE_GCODE_STATE NAME=HOMING_OVERRIDE_STATE
|
||||
|
||||
# Establish clearance before XY motion. If Z was not really homed, the
|
||||
# temporary homed flag is explicitly cleared after an XY-only request.
|
||||
{% if z_was_homed %}
|
||||
{% set lift_z = [printer.toolhead.position.z|float + 5.0, printer.toolhead.axis_maximum.z|float]|min %}
|
||||
G90
|
||||
G1 Z{lift_z} F600
|
||||
{% else %}
|
||||
SET_KINEMATIC_POSITION Z=0 SET_HOMED=Z
|
||||
G90
|
||||
G1 Z5 F600
|
||||
{% endif %}
|
||||
|
||||
{% if home_x %}
|
||||
_HOME_X
|
||||
{% endif %}
|
||||
|
||||
{% if home_y %}
|
||||
_HOME_Y
|
||||
{% endif %}
|
||||
|
||||
{% if home_z %}
|
||||
G90
|
||||
G1 X125 Y125 F15000
|
||||
G28 Z
|
||||
G1 Z10 F1500
|
||||
{% elif not z_was_homed %}
|
||||
SET_KINEMATIC_POSITION SET_HOMED= CLEAR_HOMED=Z
|
||||
{% endif %}
|
||||
|
||||
RESTORE_GCODE_STATE NAME=HOMING_OVERRIDE_STATE MOVE=0
|
||||
@@ -0,0 +1,16 @@
|
||||
[mcu adxl]
|
||||
# Change <mySerial> to whatever you found above. For example,
|
||||
# usb-Klipper_rp2040_E661640843545B2E-if00
|
||||
serial: /dev/serial/by-id/usb-Klipper_rp2040_E6625495535A5232-if00
|
||||
|
||||
[adxl345]
|
||||
cs_pin: adxl:gpio9
|
||||
spi_software_sclk_pin: adxl:gpio10
|
||||
spi_software_mosi_pin: adxl:gpio11
|
||||
spi_software_miso_pin: adxl:gpio12
|
||||
axes_map: x,-z,y
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
125, 125, 20
|
||||
@@ -0,0 +1,100 @@
|
||||
[server]
|
||||
host: 0.0.0.0
|
||||
port: 7125
|
||||
klippy_uds_address: /home/biqu/printer_data/comms/klippy.sock
|
||||
|
||||
[authorization]
|
||||
trusted_clients:
|
||||
10.0.0.0/8
|
||||
127.0.0.0/8
|
||||
169.254.0.0/16
|
||||
172.16.0.0/12
|
||||
192.168.0.0/16
|
||||
FE80::/10
|
||||
::1/128
|
||||
cors_domains:
|
||||
*.lan
|
||||
*.local
|
||||
*://localhost
|
||||
*://localhost:*
|
||||
*://my.mainsail.xyz
|
||||
*://app.fluidd.xyz
|
||||
|
||||
[octoprint_compat]
|
||||
|
||||
[history]
|
||||
|
||||
[update_manager]
|
||||
channel: dev
|
||||
refresh_interval: 168
|
||||
|
||||
[update_manager mainsail-config]
|
||||
type: git_repo
|
||||
primary_branch: master
|
||||
path: ~/mainsail-config
|
||||
origin: https://github.com/mainsail-crew/mainsail-config.git
|
||||
managed_services: klipper
|
||||
|
||||
[update_manager mainsail]
|
||||
type: web
|
||||
channel: stable
|
||||
repo: mainsail-crew/mainsail
|
||||
path: ~/mainsail
|
||||
|
||||
[update_manager crowsnest]
|
||||
type: git_repo
|
||||
path: ~/crowsnest
|
||||
origin: https://github.com/mainsail-crew/crowsnest.git
|
||||
install_script: tools/install.sh
|
||||
|
||||
# Sonar update_manager entry
|
||||
[update_manager sonar]
|
||||
type: git_repo
|
||||
path: ~/sonar
|
||||
origin: https://github.com/mainsail-crew/sonar.git
|
||||
primary_branch: main
|
||||
managed_services: sonar
|
||||
install_script: tools/install.sh
|
||||
|
||||
[update_manager timelapse]
|
||||
type: git_repo
|
||||
primary_branch: main
|
||||
path: ~/moonraker-timelapse
|
||||
origin: https://github.com/mainsail-crew/moonraker-timelapse.git
|
||||
managed_services: klipper moonraker
|
||||
|
||||
[update_manager KlipperScreen]
|
||||
type: git_repo
|
||||
path: ~/KlipperScreen
|
||||
origin: https://github.com/jordanruthe/KlipperScreen.git
|
||||
virtualenv: ~/.KlipperScreen-env
|
||||
requirements: scripts/KlipperScreen-requirements.txt
|
||||
install_script: scripts/KlipperScreen-install.sh
|
||||
managed_services: KlipperScreen
|
||||
|
||||
[update_manager klipper_tmc_autotune]
|
||||
type: git_repo
|
||||
channel: dev
|
||||
path: ~/klipper_tmc_autotune
|
||||
origin: https://github.com/andrewmcgr/klipper_tmc_autotune.git
|
||||
managed_services: klipper
|
||||
primary_branch: main
|
||||
install_script: install.sh
|
||||
|
||||
[update_manager cartographer_plugin]
|
||||
type: python
|
||||
channel: stable
|
||||
virtualenv: ~/klippy-env
|
||||
project_name: cartographer3d-plugin
|
||||
is_system_service: False
|
||||
managed_services: klipper
|
||||
info_tags: desc=Cartographer Plugin
|
||||
|
||||
[file_manager]
|
||||
enable_object_processing: True
|
||||
[update_manager klipper-backup]
|
||||
type: git_repo
|
||||
path: ~/klipper-backup
|
||||
origin: https://github.com/Staubgeborener/klipper-backup.git
|
||||
managed_services: moonraker
|
||||
primary_branch: main
|
||||
Reference in new issue
Block a user