KlipperScreen.conf modified - 06.09.2026 - 22:40:45
This commit is contained in:
klipper committed
1 parent
a50e713339
commit
d0fc210dc7
3 files changed
-172
No files matched your search
@@ -1,28 +0,0 @@
|
||||
[mcu cartographer]
|
||||
|
||||
canbus_uuid: fa54c42a161b
|
||||
|
||||
|
||||
[cartographer]
|
||||
mcu: cartographer
|
||||
# Offsets are measured from the centre of your coil, to the tip of your nozzle
|
||||
# on a level axis. It is vital that this is accurate.
|
||||
x_offset: 0
|
||||
# adjust for your cartographers offset from nozzle to middle of coil
|
||||
y_offset: 25
|
||||
# adjust for your cartographers offset from nozzle to middle of coil
|
||||
|
||||
[adxl345]
|
||||
cs_pin: cartographer:PA3
|
||||
spi_bus: spi1
|
||||
|
||||
[resonance_tester]
|
||||
accel_chip: adxl345
|
||||
probe_points:
|
||||
125, 125, 20
|
||||
|
||||
[temperature_sensor Cartographer_MCU]
|
||||
sensor_type: temperature_mcu
|
||||
sensor_mcu: cartographer
|
||||
min_temp: 0
|
||||
max_temp: 105
|
||||
@@ -1,55 +0,0 @@
|
||||
#### crowsnest.conf
|
||||
#### This is a typical default config.
|
||||
#### Also used as default in mainsail / MainsailOS
|
||||
#### See:
|
||||
#### https://github.com/mainsail-crew/crowsnest/blob/master/README.md
|
||||
#### for details to configure to your needs.
|
||||
|
||||
|
||||
#####################################################################
|
||||
#### #####
|
||||
#### Information about ports and according URL's #####
|
||||
#### #####
|
||||
#####################################################################
|
||||
#### #####
|
||||
#### Port 8080 equals /webcam/?action=[stream/snapshot] #####
|
||||
#### Port 8081 equals /webcam2/?action=[stream/snapshot] #####
|
||||
#### Port 8082 equals /webcam3/?action=[stream/snapshot] #####
|
||||
#### Port 8083 equals /webcam4/?action=[stream/snapshot] #####
|
||||
#### #####
|
||||
#####################################################################
|
||||
|
||||
|
||||
[crowsnest]
|
||||
log_path: ~/printer_data/logs/crowsnest.log
|
||||
log_level: verbose # Valid Options are quiet/verbose/debug
|
||||
delete_log: false # Deletes log on every restart, if set to true
|
||||
|
||||
[cam android]
|
||||
mode: mjpg # mjpg/rtsp
|
||||
port: 80 # Port
|
||||
device: http://192.168.0.117:4747/video # See Log for available ...
|
||||
resolution: 640x480 # widthxheight format
|
||||
max_fps: 15 # If Hardware Supports this it will be forced, otherwise ignored/coerced.
|
||||
#custom_flags: # You can run the Stream Services with custom flags.
|
||||
#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
|
||||
|
||||
[cam c930]
|
||||
mode: mjpg # mjpg/rtsp
|
||||
port: 8080 # Port
|
||||
device: /dev/video0 # See Log for available ...
|
||||
resolution: 1280x720 # widthxheight format
|
||||
max_fps: 30 # If Hardware Supports this it will be forced, otherwise ignored/coerced.
|
||||
#custom_flags: # You can run the Stream Services with custom flags.
|
||||
#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
|
||||
|
||||
[cam custom]
|
||||
mode: mjpg # mjpg/rtsp
|
||||
port: 8081 # Port
|
||||
device: /dev/video2 # See Log for available ...
|
||||
resolution: 1280x720 # widthxheight format
|
||||
max_fps: 30 # If Hardware Supports this it will be forced, otherwise ignored/coerced.
|
||||
#custom_flags: # You can run the Stream Services with custom flags.
|
||||
#v4l2ctl: # Add v4l2-ctl parameters to setup your camera, see Log what your cam is capable of.
|
||||
|
||||
|
||||
@@ -1,89 +0,0 @@
|
||||
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
||||
# Canbus board. To use this config, the firmware should be compiled for the
|
||||
# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)".
|
||||
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
||||
|
||||
# See docs/Config_Reference.md for a description of parameters.
|
||||
|
||||
|
||||
# [temperature_sensor EBB_NTC]
|
||||
# sensor_type: Generic 3950
|
||||
# sensor_pin: EBBCan:gpio28
|
||||
|
||||
# [adxl345]
|
||||
# cs_pin: EBBCan:gpio1
|
||||
# spi_software_sclk_pin: EBBCan:gpio2
|
||||
# spi_software_mosi_pin: EBBCan:gpio0
|
||||
# spi_software_miso_pin: EBBCan:gpio3
|
||||
# axes_map: z,-y,x
|
||||
|
||||
# [resonance_tester]
|
||||
# probe_points: 100, 100, 20
|
||||
# accel_chip: adxl345
|
||||
|
||||
|
||||
|
||||
|
||||
|
||||
[mcu EBBCan]
|
||||
canbus_uuid: 2bfe734774a0
|
||||
|
||||
# [adxl345]
|
||||
# cs_pin: EBBCan: PB12
|
||||
# spi_bus: spi2_PB2_PB11_PB10
|
||||
# axes_map: x,y,z
|
||||
|
||||
|
||||
[extruder]
|
||||
## Update value below when you perform extruder calibration
|
||||
## If you ask for 100mm of filament, but in reality it is 98mm:
|
||||
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
||||
rotation_distance: 47.088
|
||||
gear_ratio: 9:1
|
||||
microsteps: 16
|
||||
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
||||
nozzle_diameter: 0.340
|
||||
filament_diameter: 1.75
|
||||
max_extrude_only_distance: 50
|
||||
min_temp: 10
|
||||
max_temp: 300
|
||||
max_power: 1.0
|
||||
min_extrude_temp: 170
|
||||
max_extrude_cross_section: 5
|
||||
|
||||
## Try to keep pressure_advance below 1.0
|
||||
pressure_advance: 0.038
|
||||
## Default is 0.040, leave stock
|
||||
#pressure_advance_smooth_time: 0.040
|
||||
step_pin: EBBCan: PD0
|
||||
dir_pin: EBBCan: PD1
|
||||
enable_pin: !EBBCan: PD2
|
||||
heater_pin: EBBCan: PB13
|
||||
sensor_type: MAX31865
|
||||
sensor_pin: EBBCan: PA4
|
||||
spi_bus: spi1
|
||||
rtd_nominal_r: 1000
|
||||
rtd_reference_r: 4300
|
||||
rtd_num_of_wires: 2
|
||||
|
||||
|
||||
[tmc2209 extruder]
|
||||
uart_pin: EBBCan: PA15
|
||||
run_current: 0.650
|
||||
stealthchop_threshold: 999999
|
||||
|
||||
[fan]
|
||||
pin: EBBCan: PA1
|
||||
kick_start_time: 0.5
|
||||
hardware_pwm: false
|
||||
cycle_time: 0.01
|
||||
off_below: 0.1
|
||||
|
||||
[heater_fan hotend_fan]
|
||||
pin: EBBCan: PA0
|
||||
heater: extruder
|
||||
heater_temp: 50.0
|
||||
max_power: 1.0
|
||||
kick_start_time: 0.5
|
||||
|
||||
|
||||
Reference in new issue
Block a user