93 lines
2.0 KiB
INI
93 lines
2.0 KiB
INI
# This file contains common pin mappings for the BIGTREETECH EBBCan
|
|
# Canbus board. To use this config, the firmware should be compiled for the
|
|
# RP2040 with "USB" or "CAN bus (on gpio4/gpio5)".
|
|
# The "EBB Can" micro-controller will be used to control the components on the nozzle.
|
|
|
|
# See docs/Config_Reference.md for a description of parameters.
|
|
|
|
|
|
# [temperature_sensor EBB_NTC]
|
|
# sensor_type: Generic 3950
|
|
# sensor_pin: EBBCan:gpio28
|
|
|
|
# [adxl345]
|
|
# cs_pin: EBBCan:gpio1
|
|
# spi_software_sclk_pin: EBBCan:gpio2
|
|
# spi_software_mosi_pin: EBBCan:gpio0
|
|
# spi_software_miso_pin: EBBCan:gpio3
|
|
# axes_map: z,-y,x
|
|
|
|
# [resonance_tester]
|
|
# probe_points: 100, 100, 20
|
|
# accel_chip: adxl345
|
|
|
|
|
|
|
|
|
|
|
|
[mcu EBBCan]
|
|
canbus_uuid: 2bfe734774a0
|
|
|
|
# [adxl345]
|
|
# cs_pin: EBBCan: PB12
|
|
# spi_bus: spi2_PB2_PB11_PB10
|
|
# axes_map: x,y,z
|
|
|
|
|
|
[extruder]
|
|
## Update value below when you perform extruder calibration
|
|
## If you ask for 100mm of filament, but in reality it is 98mm:
|
|
## rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
|
|
rotation_distance: 47.088
|
|
gear_ratio: 9:1
|
|
microsteps: 16
|
|
full_steps_per_rotation: 200 #200 for 1.8 degree, 400 for 0.9 degree
|
|
nozzle_diameter: 0.340
|
|
filament_diameter: 1.75
|
|
max_extrude_only_distance: 50
|
|
min_temp: 10
|
|
max_temp: 300
|
|
max_power: 1.0
|
|
min_extrude_temp: 170
|
|
max_extrude_cross_section: 5
|
|
control = pid
|
|
pid_kp = 26.213
|
|
pid_ki = 1.304
|
|
pid_kd = 131.721
|
|
## Try to keep pressure_advance below 1.0
|
|
pressure_advance: 0.020
|
|
## Default is 0.040, leave stock
|
|
#pressure_advance_smooth_time: 0.040
|
|
step_pin: EBBCan: PD0
|
|
dir_pin: !EBBCan: PD1
|
|
enable_pin: !EBBCan: PD2
|
|
heater_pin: EBBCan: PA2
|
|
sensor_type: MAX31865
|
|
sensor_pin: EBBCan: PA4
|
|
spi_bus: spi1
|
|
rtd_nominal_r: 1000
|
|
rtd_reference_r: 4300
|
|
rtd_num_of_wires: 2
|
|
|
|
|
|
[tmc2209 extruder]
|
|
uart_pin: EBBCan: PA15
|
|
run_current: 0.650
|
|
stealthchop_threshold: 999999
|
|
|
|
[fan]
|
|
pin: EBBCan: PA0
|
|
kick_start_time: 0.5
|
|
hardware_pwm: false
|
|
cycle_time: 0.01
|
|
off_below: 0.1
|
|
|
|
[heater_fan hotend_fan]
|
|
pin: EBBCan: PA1
|
|
heater: extruder
|
|
heater_temp: 50.0
|
|
max_power: 1.0
|
|
kick_start_time: 0.5
|
|
|
|
[neopixel hotend_rgb]
|
|
pin: EBBCan:PD3 |