sample-bigtreetech-ebb-sb-rp2040-canbus-v1.0.cfg modified - 21.11.2025 - 00:13:01

printer_data/config/sample-bigtreetech-ebb-sb-rp2040-canbus-v1.0.cfg

@@ -5,12 +5,10 @@
 
 # See docs/Config_Reference.md for a description of parameters.
 
-[mcu EBBCan]
-canbus_uuid: c56f89ac8cb9
 
-[temperature_sensor EBB_NTC]
-sensor_type: Generic 3950
-sensor_pin: EBBCan:gpio28
+# [temperature_sensor EBB_NTC]
+# sensor_type: Generic 3950
+# sensor_pin: EBBCan:gpio28
 
 # [adxl345]
 # cs_pin: EBBCan:gpio1
@@ -26,21 +24,70 @@ sensor_pin: EBBCan:gpio28
 
 
 
+
+[mcu EBBCan]
+canbus_uuid: 2bfe734774a0
+
+# [adxl345]
+# cs_pin: EBBCan: PB12
+# spi_bus: spi2_PB2_PB11_PB10
+# axes_map: x,y,z
+
+
+[extruder]
+##  Update value below when you perform extruder calibration
+##  If you ask for 100mm of filament, but in reality it is 98mm:
+##  rotation_distance = <previous_rotation_distance> * <actual_extrude_distance> / 100
+rotation_distance: 47.088
+gear_ratio: 9:1
+microsteps: 16
+full_steps_per_rotation: 200    #200 for 1.8 degree, 400 for 0.9 degree
+nozzle_diameter: 0.340
+filament_diameter: 1.75
+max_extrude_only_distance: 50
+min_temp: 10
+max_temp: 300
+max_power: 1.0
+min_extrude_temp: 170
+max_extrude_cross_section: 5
+control = pid
+pid_kp = 26.213
+pid_ki = 1.304
+pid_kd = 131.721
+##  Try to keep pressure_advance below 1.0
+pressure_advance: 0.020
+##  Default is 0.040, leave stock
+#pressure_advance_smooth_time: 0.040
+step_pin: EBBCan: PD0
+dir_pin: !EBBCan: PD1
+enable_pin: !EBBCan: PD2
+heater_pin: EBBCan: PA2
+sensor_type: MAX31865
+sensor_pin: EBBCan: PA4
+spi_bus: spi1
+rtd_nominal_r: 1000
+rtd_reference_r: 4300
+rtd_num_of_wires: 2
+
+
 [tmc2209 extruder]
-uart_pin: EBBCan:gpio20
-run_current: 0.6
-stealthchop_threshold: 0
+uart_pin: EBBCan: PA15
+run_current: 0.650
+stealthchop_threshold: 999999
 
 [fan]
-pin: EBBCan:gpio13
+pin: EBBCan: PA0
 kick_start_time: 0.5
 hardware_pwm: false
 cycle_time: 0.01
 off_below: 0.1
 
 [heater_fan hotend_fan]
-pin: EBBCan:gpio14
+pin: EBBCan: PA1
 heater: extruder
 heater_temp: 50.0
 max_power: 1.0
-kick_start_time: 0.5
+kick_start_time: 0.5
+
+[neopixel hotend_rgb]
+pin: EBBCan:PD3